K-Buffer

The K-Buffer by Foxpedal is a guitar effects pedal designed with the following features and technical specifications: \- Op-Amp based circuit \- High input impedance to ensure a strong and clear signal \- Mini form factor for compact pedalboard integration \- Handwired construction for quality and durability \- Quality hand-wired closed frame jacks \- Power: Standard 9 volt DC with negative center, no internal battery option \- Dimensions: 1.5" width x 3.6" height x 1.2" depth \- Current Draw: Approximately 15mA The K-Buffer is built using a classic buffer design similar to the famous Klon Centaur, offering musicians the essential function of buffering their guitar signal.

Refinery V2

The Refinery V2 by Foxpedal is a five-knob compressor designed for ultimate control over the signal. It is built around an Operational Transconductance Amplifier (OTA), offering an incredibly low noise floor and more headroom. The Refinery V2 provides control over various parameters: 1\. Attack: Determines the time it takes for the compression to engage when a loud signal is introduced. 2\. Release: Controls the time it takes for the gain to recover after the loud signal has passed. 3\. Ratio: Adjusts how much the gain reduces during compression, with the ability to blend uncompressed signal with the compressed response. 4\. Level: Allows the re-addition of gain to recover any lost volume during compression. 5\. Blend (New! ): Maintains the clean (dry) and compressed (wet) signals in two parallel paths, enabling mixing between full-dry and full-wet with minimal signal loss. 6\. Bright Toggle: Provides the option to boost treble frequencies to add sparkle back to a compressed signal. The dimensions of the Refinery V2 are 2.6" W x 4.6" H x 1.5" D, with a current draw of approximately 30mA. The design is based on the Engineer's Thumb circuit by Merlin Blencoe of valvewizard.co.uk, with permission granted to create a commercial product using this circuit.

The Wave

The Wave by Foxpedal is a dual delay, reverb, and modulation pedal that delivers classic tape delay sounds in an Analog/Digital hybrid. It features dual programmable delay times, allowing users to dial in various ambiance from simple slap-back to outer space effects. The pedal includes three classic tape delay modes: Binson Echorec, Roland RE-201 Space Echo, and Echoplex EP-3. Additionally, it offers tape-style warble modulation to the delay signal and a new Belton V3 reverb brick for creating dark natural vibes. The pedal's dimensions are 5.6" x 4.6" x 1.6", and it has a current draw of approximately 120mA.

Wrath V2

The Wrath V2 by Foxpedal features a genuine LM308 Op-Amp and a Reutz mod with a red LED clipping option. The Reutz mod, controlled by the "Sweep" control, adjusts the clipping frequency of the gain stage, resulting in a darker tone as it is turned up. The pedal is powered by a standard 9-volt DC with a negative center, and it does not have an internal battery option. It is equipped with a 3PDT True Bypass Footswitch and has dimensions of 2.6" width, 4.6" height, and 1.5" depth. The current draw is approximately 15mA. The construction is handwired, and it features quality hand-wired open frame jacks. Additionally, the updated V2 model includes top-mount jacks, a soft- touch relay bypass switch, and updated "ghost black polygon" graphics.

Defector Fuzz

The Defector Fuzz by Foxpedal is a versatile pedal with the following technical specifications and features: \- Classic four-stage transistor Fuzz \- Independent linear pre-boost \- Special "Feedback" mode unlocks unique and extreme tones \- 3-way clipping switch \- Mids control for full tone customization \- Neutrik top-mount jacks \- Soft-touch switching \- 9V Center-negative standard power supply \- Made In USA \- Dimensions: 2.6"W x 4.6"H x 1.5"D \- Current Draw: ~20mA This pedal offers a range of tonal possibilities and is designed for musicians seeking a high-quality and customizable fuzz effect.

Kingdom Combo V2

The Kingdom Combo V2 by Foxpedal features NOS D9E Germanium Diodes, overdrive and clipping options, top mount jacks, and a soft-touch bypass footswitch. It is powered by a standard 9-volt DC with no internal battery option, and has dimensions of 2.6" width, 4.6" height, and 1.5" depth, with a current draw of approximately 40mA. The pedal is made in the USA and includes a new boost "Focus" knob for adjusting the bandwidth of frequency range in the boost section.

The City

The City V2 by Foxpedal is an overdrive pedal with a range of features and technical specifications. Here are the details: \- The City V2 features an updated boost section using the powerful Ebenezer boost and a much smaller form-factor, top-mount jacks, and soft-touch relay switching. \- It offers full control over the drive, including level, body, tone, and drive, allowing for a wide range of tonal shaping. \- The pedal provides two clipping options: Red LED for loud, aggressive tones and MOSFET for textured smoothness. \- It includes a presence control to add treble clipping for livelier single- note playing and a flat switch to lessen the mid focus. \- The City V2 also features an independent MOSFET clean boost (the same as the Ebenezer) for added flexibility in pushing the gain for solos or adding more dirt to the tone. \- Technical specifications include top jacks, standard 9-volt DC power with negative center, and relay bypass soft-touch switching. \- The pedal is made in the USA and has dimensions of 2.6" W x 4.6" H x 1.5" D. The City V2 is designed to provide guitarists with a flexible and dynamic overdrive experience, offering a classic drive circuit with modern features and controls.

Killface

The Killface V2 by Foxpedal is a Bass-tuned transparent overdrive pedal designed for bass players. It features overdrive and clipping options, NOS D9E Germanium Diodes, top-mount jacks, and SMT construction. The pedal operates on a standard 9-volt DC power supply with negative center, and it does not have an internal battery option. The dimensions of the pedal are 2.6" width, 4.6" height, and 1.5" depth, with a current draw of approximately 40mA. Additionally, it is equipped with a soft-touch relay bypass footswitch and is made in the USA.

Slow Hound

Ebenezer

The Ebenezer by Foxpedal is a clean MOSFET boost pedal designed with a MOSFET- based circuit for natural tones and high input impedance. It features a mini form factor, handwired construction, and a milled aluminum knurled knob. The pedal also includes quality hand-wired closed frame jacks and operates on a standard 9-volt DC power supply with no internal battery option. The Ebenezer is equipped with a 3PDT true bypass footswitch and has dimensions of 1.5" width, 3.6" height, and 1.2" depth, with a current draw of approximately 10mA.

Magnifica Reverb

The Magnifica Reverb by Foxpedal features hand-built construction and controls for feedback, tone, and reverb. It offers the ability to adjust the amount of wet, control the tone of the reverberated signal, and dial in the amount of reverb that's fed back into itself. The pedal is designed with top jacks, relay bypass soft-touch switching, and operates on a standard 9-volt DC power supply with no internal battery option. The unit will not produce a full wet, no-dry signal, as there is always some amount of dry signal mixed in. The dimensions of the pedal are 2.6" W x 4.6" H x 1.5" D, with a current draw of approximately 130mA. The circuit design is inspired by circuits designed by CultureJam and GrindCustomFX.

The Wave

The Wave by Foxpedal is a dual delay, reverb, and modulation pedal that delivers classic tape delay sounds in an Analog/Digital hybrid. It features dual programmable delay times, allowing users to dial in various ambiance from simple slap-back to outer space effects. The pedal includes three classic tape delay modes: Binson Echorec, Roland RE-201 Space Echo, and Echoplex EP-3. Additionally, it offers tape-style warble modulation to the delay signal and a new Belton V3 reverb brick for creating dark natural vibes. The pedal's dimensions are 5.6" x 4.6" x 1.6", and it has a current draw of approximately 120mA.