Dual Bass Station DBS-1

The Providence DBS-1 Dual Bass Station is a high-quality bass preamp designed for professional use. It features two inputs (A/B) and independent EQ-Masters for each input, allowing for versatile sound shaping and control. When only "IN-A" is used, two different presets can be utilized by switching channels from A to B. Both channels are equipped with versatile 3-band equalizers suitable for a wide range of musical genres and playing styles. Key Technical Specifications: \- Controls: BASS, MID, MID FREQ, TREBLE, MASTER / A_B each channel, MUTE, A/B \- Connectors: Standard 1/4-inch phone jacks (IN-A, IN-B, OUT, TUNER), DC12V input jack \- Electrical characteristics: BASS 60Hz±14dB peaking, MID 150Hz–1kHz±14dB peaking, TREBLE 3kHz±14dB peaking, MASTER -∞ to +10dB, Output noise level -95dBu or less (IHF A.W.T.D), Harmonic distortion 0.01% or less (Output 0dBu) \- Power Supply: Supplied AC adaptor (PAP-712DCJ for North America and Japan, PAP-712DCE for Europe, PAP-712DCU for UK) \- Power Consumption: DC12V, 110mA \- Dimensions: 122mm (D) x 101mm (W) x 58mm (H) \- Weight: Approximately 370g (excluding AC adaptor) The internal circuitry is powered by a 24-volt supply, enabling expressive dynamic range and clarity for bass guitar performance. The unit is built with high-quality components to achieve ultra-low noise (over S/N -95db) and low distortion rate (under 0.01%), meeting the demands of professional musicians. The DBS-1 Dual Bass Station is suitable for bass players seeking precise control over their sound and is designed to integrate seamlessly into a professional signal chain.

Vitalizer WV

The Vitalizer WV by Providence, model VZW-1, is an active impedance converter designed to enhance sound quality when using a passive-pickup guitar with wah or volume pedals. It converts high impedance signals, which are prone to degradation and noise, into low impedance signals, preserving the original sound quality. Specifications: \- Connectors: 1/4-inch phone jack x 2 (INPUT and OUTPUT), DC 9V input jack (AC adaptor jack) \- Power Supply: 9V battery or AC adaptor \- Power Consumption: DC 9V, 3 mA approx. (effect ON) \- Dimensions: 60(D) x 73(W) x 43(H)mm \- Weight: 100 g approx. \- Supplied Accessories: Outer Battery Box LE-OBB-2, 006P 9V Battery (6F22) Use Cases: The Vitalizer WV is particularly effective when placed next to wah or volume pedals, minimizing tonal changes and signal degradation. It can be positioned at the last position before the amp or the first position after the guitar to control the signal with minimized degradation on pedals. Design: The pedal is designed in a small chassis (60x73mm), allowing it to be placed in a small space on the pedalboard. It can be powered by a 9V battery or an AC adaptor, providing flexibility in usage. Functionality: The Vitalizer WV actively converts high impedance signals to low impedance signals, ensuring minimal degradation and noise pickup. It is designed to deliver a natural, faithful instrument sound while respecting the character of guitar and effect pedal signals. Overall, the Vitalizer WV serves as an essential tool for maintaining sound quality and minimizing signal degradation when using passive-pickup guitars with wah or volume pedals.

Anadime Chorus ADC-4

The Anadime Chorus ADC-4 by Providence is a versatile analog chorus effect pedal designed to deliver a rich and warm sound. It utilizes a BBD (Bucket Brigade Delay) device to achieve a traditional, warm, and full analog chorus effect. Despite producing a mono output, the pedal creates a spacious sense of width and depth, as well as warmth and thickness characteristic of analog choruses. Key Features: \- Multi-function LED: Indicates the pedal's on/off status and provides visual battery power monitoring. When the battery voltage drops below 7 volts, the LED dims, signaling the need for battery replacement. \- S.C.T Circuit: Incorporates a Single Contact True Bypass circuit, ensuring unprecedented signal quality and reliability by minimizing the instrument signal's passage through switch contacts when bypassed. \- D.C.G. Circuit: Features a Double Contact Grounding Circuit to maximize sonic quality by grounding the plug inserted into the output jack at two contact points, reducing the possibility of intermittent contact. Specifications: \- Controls: Depth, Speed, Mix, Deep (3-way mode switch) \- Jacks: Standard 1/4-inch phone jacks (Input/Output), DC9V Input jack (AC adaptor jack) \- Power: 9V battery (1), AC adaptor \- Power Consumption: DC9V approx. 26mA (with effect turned ON) \- Size: 115(D) X 73(W) X 50(H)mm \- Weight: Approx. 250g (without battery) The pedal's 3-way mode switch allows for the creation of a variety of sounds, providing variations in the perceived dimensional depth. The Anadime Chorus ADC-4 is suitable for a wide range of applications, from moody arpeggios to powerful riffs and solos, making it an ideal choice for guitarists seeking a classic analog chorus effect.

Velvet Comp VLC-1

The Providence Velvet Comp VLC-1 is a compressor pedal designed to provide smooth, lustrous compression with a wide sustain range, suitable for various playing styles. The pedal features controls for LEVEL, ATTACK, and SUSTAIN, allowing users to adjust the compression to match different playing techniques, from arpeggios to crisp chording. The dimensions of the pedal are 115 (D) x 72 (W) x 50 (H) mm, and it weighs approximately 250 g (excluding the battery). The connectors include 1/4-inch phone jack x 2 (INPUT and OUTPUT) and a DC 9V input jack (AC adaptor jack). The power supply can be either a 9V battery or an AC adaptor, with a power consumption of DC 9V, 5 mA approx. (effect ON). The pedal is equipped with the S.C.T Circuit, which ensures unmatched signal quality and reliability by utilizing a Single Contact True Bypass configuration. Additionally, it features a multi-function LED that indicates the pedal's on/off status and provides visual battery power monitoring. When the battery voltage drops below 7 volts, the LED will become dimmer and begin to go out, signaling the need for battery replacement to ensure optimum performance.

DLY-4 Chrono Delay

The Providence DLY-4 Chrono Delay is a digital delay pedal with a range of features and precise control capabilities. Here are the technical specifications and details: \- Delay Time: Adjustable from 1 to 2700 milliseconds \- Display Modes: Switchable between milliseconds (mSec) and beats per minute (BPM) with metronome accuracy \- Tap Tempo: Allows precise setting of delay time according to the tempo tapped on the TPA switch \- A/B Preset Memory: Memorizes and recalls two different delay time settings via the footswitch \- Beat Split: Offers seven delay time variations ranging from half-notes to eight-note triplets, based on a specified delay time as a quarter-note reference \- Analog Circuitry with VITALIZER®: Prevents degradation of the direct signal and combines the direct signal with the delay signal using high-performance analog circuits \- External Tap Input: Allows remote tap delay operation using a momentary footswitch connected to the EXT.TAP jack \- Power Supply: Requires the supplied AC power adapter (PAP-712DCJ for North America and Japan, PAP-712DCE for Europe) \- Power Consumption: DC12V, 110mA \- Dimensions: 122mm (D) x 101mm (W) x 58mm (H) \- Weight: Approximately 0.41 kg The DLY-4 Chrono Delay provides a high-resolution delay effect with extraordinary depth, precise control, and a simple interface for fast, intuitive operation. It maintains the direct signal in the analog domain from input to output, ensuring minimal signal degradation and latency. The pedal's compact enclosure houses a comprehensive set of controls for achieving clean, crisp repeats and optimum delay time control.

Heat Blaster HBL-3

The Providence Heat Blaster HBL-3 is a powerful distortion pedal designed to deliver a modern high-gain tube amplifier sound. It builds upon the features of the earlier HBL-2 version, enhancing the overtone-rich high-gain tube amp sound with fatter lows and mids for increased presence and power. The pedal retains fast response for outstanding articulation and is ideal for use with the clean channel of a multi-channel amplifier. Key Features: \- Controls: LEVEL, TONE, DRIVE, BASS BOOST \- BASS BOOST Switch: Boosts the low-frequency range, achieving extra low-end impact with humbucking and single-coil pickups \- S.C.T. Circuit: Features a single contact true-bypass circuit for higher sound quality and reliability, reducing any change or deterioration in sound quality \- D.C.G. Circuit: Utilizes a double-contact grounding circuit to improve sound quality and prevent loose connections \- Multi-function LED: Indicates the pedal's on/off status and provides visual battery power monitoring Technical Specifications: \- Connectors: 1/4-inch phone jack x 2 (INPUT and OUTPUT), DC 9V input jack (AC adaptor jack) \- Power Supply: 9V battery or AC adaptor \- Power Consumption: DC 9V, 8 mA approx. \- Dimensions: 115(D) x 72(W) x 50(H)mm \- Weight: 250 g approx. (Not including battery) The Providence Heat Blaster HBL-3 is designed to offer tube-amp type sensitivity, allowing picking nuances to be fully expressed in the tone without excessive compression. It is a versatile distortion pedal suitable for various musical styles, from classic rock to modern hard rock, and is well- suited for professional musicians and enthusiasts seeking a high-quality distortion effect.

Final Booster FBT-1

Brick Drive BDI-1

The Providence Brick Drive BDI-1 is a bass preamp pedal designed to deliver high-quality sound and versatile functionality. Here are the technical specifications and features: \- Employs Vitalizer B circuit in the input section, which converts high impedance signals to low impedance signals, minimizing degradation of sound quality and delivering natural, faithful instrument sound. \- The Vitalizer B circuit tightens up the bottom end, providing more vivid and clear sound compared to other processors and effects. \- Internal operating voltage boosted to 21V for increased dynamic range and low noise. \- Mix control allows blending of drive sound and clean sound through the preamp EQ, adding nuance to the overdriven sound. \- EQ section based on the Dual Bass Station's circuit, featuring controls for Treble, Mid, Bass, and Presence for precise tone shaping. \- Loaded with a balanced XLR DI out for flexibility in both live and recording environments, with a ground lift switch to prevent ground loop noise. \- Bypass/Mute switch for selecting the mode when the pedal is bypassed, offering direct sound bypassing the Vitalizer B circuit or mute mode for instrument switching or tuning. \- Controls: CLEAN LEVEL, DRIVE LEVEL, MIX, DRIVE GAIN, BASS, MID, MID FREQ, TREBLE, PRESENCE, BYPASS/MUTE MODE SW, BYPASS/MUTE-OFF SW, CLEAN-DRIVE SW, GND LIFT SW \- Connectors: Standard 1/4-inch Phone JACK (IN, OUT, VZ THRU), XLR TYPE (DI OUT), DC12V INPUT \- Power consumption: DC12V 80mA (Power supply NOT included) \- Size: 125(D) X 97(W) X 50(H)mm \- Weight: Approx. 380g

Red Rock OD ROD-1

The Providence Red Rock OD ROD-1 is a warm overdrive pedal designed to provide plenty of sustain, giving guitarists a wide-ranging expressive voice. The tone is specifically tailored for guitars with single-coil pickups. The pedal features the following technical specifications: \- Controls: VOLUME, MASTER, TONE, GAIN, FAT \- Connectors: 1/4-inch phone jack x 2 (INPUT and OUTPUT), DC 9V input jack (AC adaptor jack) \- Power Supply: 9V battery or AC adaptor \- Power Consumption: DC 9V, 20mA approx. \- Dimensions: 115(D)×73(W)×50(H)mm \- Weight: 250 g approx. (Not including battery) Additionally, the pedal incorporates a FAT switch that boosts the low frequencies to deliver a fatter, more powerful sound. It also features a wide dynamic range achieved through internal circuitry that doubles the 9-volt supply voltage to 18 volts, surpassing conventional overdrive effects. The ROD-1 utilizes the Single Contact True Bypass configuration to ensure unmatched signal quality and reliability. Furthermore, the adoption of the new double-contact grounding circuit (D.C.G. Circuit) enhances sound quality and minimizes the risk of loose connections. The pedal's multi-function LED not only indicates the on/off status but also provides effective visual battery power monitoring. When the battery voltage drops below 7 volts, the LED dims and begins to go out, signaling the need for a battery replacement to ensure optimum performance.

Stampede OD SOV-2

The Providence Stampede OD SOV-2 is a high-quality overdrive pedal designed to deliver natural overdrive without masking the inherent characteristics and tone of the guitar being used. It features a special bipolar power supply that powers the internal circuitry with boosted voltage, providing a wider dynamic range than possible with conventional 9-volt powered overdrives. Key Specifications: \- Controls: LEVEL, TONE, DRIVE \- Connectors: 1/4-inch phone jack x 2 (INPUT and OUTPUT), DC 9V input jack (AC adaptor jack) \- Power Supply: 9V battery or AC adaptor \- Power Consumption: DC 9V, 90 mA approx. (effect ON) \- Dimensions: 115(D)×72(W)×50(H)mm \- Weight: 250 g approx. (Not including battery) The pedal's Single Contact True Bypass (S.C.T) configuration ensures that the signal only passes through one switch contact when bypassed, enhancing signal quality and reliability. Additionally, the multi-function LED not only indicates the pedal's on/off status but also provides visual battery power monitoring. The Stampede OD SOV-2 is suitable for achieving singing lead tones and solid, chunky rhythms, making it a versatile tool for guitarists seeking a wide range of expressive overdrive sounds.

Vitalizer WV

The Vitalizer WV by Providence, model VZW-1, is an active impedance converter designed to enhance sound quality when using a passive-pickup guitar with wah or volume pedals. It converts high impedance signals, which are prone to degradation and noise, into low impedance signals, preserving the original sound quality. Specifications: \- Connectors: 1/4-inch phone jack x 2 (INPUT and OUTPUT), DC 9V input jack (AC adaptor jack) \- Power Supply: 9V battery or AC adaptor \- Power Consumption: DC 9V, 3 mA approx. (effect ON) \- Dimensions: 60(D) x 73(W) x 43(H)mm \- Weight: 100 g approx. \- Supplied Accessories: Outer Battery Box LE-OBB-2, 006P 9V Battery (6F22) Use Cases: The Vitalizer WV is particularly effective when placed next to wah or volume pedals, minimizing tonal changes and signal degradation. It can be positioned at the last position before the amp or the first position after the guitar to control the signal with minimized degradation on pedals. Design: The pedal is designed in a small chassis (60x73mm), allowing it to be placed in a small space on the pedalboard. It can be powered by a 9V battery or an AC adaptor, providing flexibility in usage. Functionality: The Vitalizer WV actively converts high impedance signals to low impedance signals, ensuring minimal degradation and noise pickup. It is designed to deliver a natural, faithful instrument sound while respecting the character of guitar and effect pedal signals. Overall, the Vitalizer WV serves as an essential tool for maintaining sound quality and minimizing signal degradation when using passive-pickup guitars with wah or volume pedals.

Flame Drive FDR-1

The Providence Flame Drive FDR-1 is an extremely versatile overdrive pedal designed to deliver a wide range of tones, from sweet, silky overdrive to edgy overtone-rich distortion. It features a modern high-gain overdrive sound with fast attack response, allowing it to follow detailed picking nuances. The pedal is known for its eminently musical, amp-like distortion that is never flat or muddy. Key Features: \- Controls: LEVEL, TONE, DRIVE, BASS BOOST \- Connectors: 1/4-inch phone jack x 2 (INPUT and OUTPUT), DC 9V input jack (AC adapter jack) \- V.N.S. Circuit: Vitalized Noiseless Switching Circuit minimizes switching noise while maintaining optimum sound quality \- D.C.G. Circuit: Double-contact grounding circuit provides improved sound quality and minimizes the risk of loose connections \- Bass Boost Switch: Engages the BASS BOOST function to boost low frequencies \- VITALIZER® Circuit: Prevents signal degradation, active even when the effect is off \- Multi-function LED: Indicates the pedal’s on/off status and provides visual battery power monitoring \- Power Supply: 9V battery or AC adapter \- Power Consumption: DC 9V, 8 mA approx. \- Dimensions: 115 (D) x 72 (H) x 50 (H) mm \- Weight: 250 g approx. (Not including battery) The Providence Flame Drive FDR-1 is designed to provide high-quality overdrive and distortion effects while maintaining signal integrity and responsiveness to playing nuances. It is suitable for a wide range of musical styles and playing techniques, making it a versatile tool for guitarists seeking dynamic and expressive tonal options.

Phase Force PHF-1

The Providence Phase Force PHF-1 is a phase shifter pedal designed to provide a wide range of phase shift sounds while retaining the natural characteristics of the instrument. The pedal features speed and output level controls, allowing users to achieve gentle undulations to wild variations in sound. The level control can be optimized to match the user's phrasing, and engaging the MID SHIFT switch alters the phase shift range, emphasizing mid-high frequencies. The pedal also includes a built-in VITALIZER® circuit, which enables a unique phase shift sound while allowing the natural characteristics of the instrument to come through. The VITALIZER® circuit remains active when the effect is turned off, delivering an ideal signal to processors connected after the Phase Force pedal. Additionally, the PHF-1 is equipped with a multi-function LED that indicates the pedal's on/off status and provides visual battery power monitoring. When the battery voltage drops below 7 volts, the LED will become dimmer and begin to go out. The effect will still operate at this voltage, but it is recommended to replace the battery for optimum performance. Technical Specifications: \- Controls: LEVEL, SPEED, MID SHIFT \- Connectors: 1/4-inch phone jack x 2 (INPUT and OUTPUT), DC 9V input jack (AC adaptor jack) \- Power Supply: 9V battery or AC adaptor \- Power Consumption: DC 9V, 5 mA approx. (effect ON) \- Dimensions: 115(D)×72(W)×50(H)mm \- Weight: 250 g approx. (Not including battery) The Providence Phase Force PHF-1 is designed for guitarists and musicians seeking versatile phase shifting capabilities with precise control over speed, output level, and frequency emphasis.

Brick Drive BDI-1

The Providence Brick Drive BDI-1 is a bass preamp pedal designed to deliver high-quality sound and versatile functionality. Here are the technical specifications and features: \- Employs Vitalizer B circuit in the input section, which converts high impedance signals to low impedance signals, minimizing degradation of sound quality and delivering natural, faithful instrument sound. \- The Vitalizer B circuit tightens up the bottom end, providing more vivid and clear sound compared to other processors and effects. \- Internal operating voltage boosted to 21V for increased dynamic range and low noise. \- Mix control allows blending of drive sound and clean sound through the preamp EQ, adding nuance to the overdriven sound. \- EQ section based on the Dual Bass Station's circuit, featuring controls for Treble, Mid, Bass, and Presence for precise tone shaping. \- Loaded with a balanced XLR DI out for flexibility in both live and recording environments, with a ground lift switch to prevent ground loop noise. \- Bypass/Mute switch for selecting the mode when the pedal is bypassed, offering direct sound bypassing the Vitalizer B circuit or mute mode for instrument switching or tuning. \- Controls: CLEAN LEVEL, DRIVE LEVEL, MIX, DRIVE GAIN, BASS, MID, MID FREQ, TREBLE, PRESENCE, BYPASS/MUTE MODE SW, BYPASS/MUTE-OFF SW, CLEAN-DRIVE SW, GND LIFT SW \- Connectors: Standard 1/4-inch Phone JACK (IN, OUT, VZ THRU), XLR TYPE (DI OUT), DC12V INPUT \- Power consumption: DC12V 80mA (Power supply NOT included) \- Size: 125(D) X 97(W) X 50(H)mm \- Weight: Approx. 380g